|
? | Page d'accueil | Didacticiel
|
Objectif : enregistrer une chanson rock complète (guitares, basse, synthés, batterie et chant) avec un résultat crédible : bonne qualité de son, mix clair. Tout cela en enregistrant chez soi, seul sur un PC.
Je vais vous parler ici de la façon dont je procède pour enregistrer mes chansons. C'est ma manière de faire, ce n'est ni la seule, ni sans doute la meilleure, mais elle me donne satisfaction et je la partage donc avec vous. Je ne suis pas ingénieur du son, je n'ai pas suivi de cours d'enregistrement ni de mixage et tout ce que je connais, je l'ai appris sur le tas, en pratiquant, et aussi en interrogeant des gens autour de moi ou en consultant des sites Internet spécialisés. Au final, j'ai retenu ce qui fonctionnait pour moi, mais ma méthodologie change graduellement, en fonction de l'expérience, de mes essais, de mes erreurs et de conseils que je peux glaner à droite à gauche. Surtout, n'hésitez pas à faire différemment si vous l'estimez nécessaire ou préférable. Toujours est-il que pour les débutants, cela constituera un guide efficace.
Page de messages n° 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Nico
le 16/03/2020 à 01h12
Bonjour,
J'ai essayé de me créer des IR avec Voxengo Deconvolver mais je n'obtiens que des fichiers de 1K qui sont vides.
Avez-vous une idée du problème ?
Merci par avance.
Peekup
le 22/02/2020 à 08h47
Bonjour, j'ai testé récemment une simu ampli.il me semble qu'on pouvait changer le skin des amplis (skaï revêtement, boutons contrôle).sauriez vous me dire le nom de cette simu? merci d'avance et félicitations pour le site, une vraie mine d'or.thierry
billynilly
le 18/01/2020 à 18h08
Whatever happened to the Cranked AC plugin? I've been looking all over for it but can't find it anywhere.
* * * * * * * * * * * * * * * *
Sorry, I never heard of this plugin. If it's an old plugin, chances are it's also a 32-bit plugin, which may not work properly on modern systems, but anyway I couldn't find it either.
Grebz
Kovrm
le 12/01/2020 à 23h06
So the chain goes:
DAW > Audio Interface Out > Amp > Speaker > Mic > DAW
This is correct based on my understanding from what I've read, and the few videos I've watch on creating IRs. My question, then, is when I plug into the Amp I've seen people say plug your Interface out into the FX return, but you say the guitar cable jack. What is the purpose in doing one or the other?
Side questions:
What channel should my amp be on? I'm assuming the clean channel.
What should my Amp settings be (EQ, Gain, Channel Volume, Presence, Master Volume)? I can't find a clear answer anywhere.
* * * * * * * * * * * * * * * *
Hello,
About plugging into the FX return or the guitar jack, I don’t know. Actually, the amps I’ve used myself to make IRs don’t have any FX return, so I didn’t have a choice and had to plug into the guitar jack. I guess there’s no harm trying both (not at the same time!) and comparing if you have that possibility. Chances are there’s not much of a difference, but again, I may be wrong as I have not tried this myself.
About the choice of a channel, and the settings: the channel doesn’t actually matter. You’re not capturing the amp sound, but the speaker sound.
From what I’ve experienced, the EQ and Presence should be neutral, the gain/saturation should not be engaged (or set to a level where no distorsion can be heard). As for the volume, set it to a level that’s high enough for your microphone to be able to pick up a good signal (no need to record higher than -6 dB, by the way, give your signal a bit of headroom).
But you should also be careful not to set it too loud to protect your own ears. It doesn’t need to be pushed too high. I think a level high enough to cover your own conversational voice should be enough. I tried various volume levels, and it did not affect the results notably. I did not get better results with very high levels than with normal, humanely bearable levels. Don’t set it too low, though, because it’s better if your speaker does move some air.
Experiment, try different amp settings and see whether that changes the results.
Grebz
William
le 20/10/2019 à 17h06
Hey, I downloaded the plug-in and extracted it. Then put it in the plugin folder but it is not working. C:|Program Files|Common Files|Avid|Audio|Plug-Ins. Would this be the right steps? Please let me know thanks!
* * * * * * * * * * * * * * * *
As you explained it to me by e-mail, you were using Pro Tools First, which doesn't support third party plugins. The solution is then to either upgrade to a paid version of Pro Tools, or use another free DAW, such as Cakewalk by Bandlab (Windows only), or use Reaper, which is not free, but can be used freely without constraints. These DAWs do support third party plugins.
Grebz